MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear with breakers in an industrial room, with loose conduit and fittings in the foreground.
AMERICAN BUILT   /   CALIFORNIA SERVED

Continuous Current and Peak Demand

Distinguish the current an assembly must carry continuously from short-duration demand peaks—and use both measurements in sound equipment selection.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Define the Two Current Values

Continuous current is the current an assembly is designed to carry under specified operating conditions over time. It is a rating-related design input associated with the equipment nameplate and the applicable assembly design; it is not a forecast of the facility’s moment-to-moment consumption. Peak demand, by contrast, describes a high measured or calculated load during a defined interval or event. Its meaning depends on how it was captured: an interval meter reading, a logged maximum, and a millisecond-scale inrush measurement are not interchangeable. A brief peak may exceed the ordinary running load without representing a continuous requirement. Conversely, a moderate recorded peak does not establish that an assembly can safely carry a proposed continuous load. Keep the terms separate in schedules, drawings, and submittals, and state the measurement basis and duration whenever reporting demand.

Match the Rating to the Operating Load

Equipment selection begins with the expected sustained operating current, the supply characteristics, and the relevant design conditions—not simply the largest number visible on a utility bill. Identify which loads operate together, which are intermittent, and whether planned expansion or operating changes will alter the normal profile. Account for applicable ambient, enclosure, installation, and conductor conditions in the engineering review, since ratings and allowable loading depend on the specific equipment design and governing requirements. Do not assume a nameplate value is equivalent to an everyday demand target, or that demand below that value automatically proves suitability. Qualified professionals must determine the required ratings, protection, and applicable codes for each project. A clear distinction between continuous load and temporary loading helps prevent oversizing based on a brief event while avoiding the opposite mistake of treating a short historical sample as the complete design basis.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Interpret Peaks by Duration and Cause

A peak has practical significance only when its magnitude, duration, recurrence, and source are understood. Motor starting, transformer energization, welding, charging systems, and simultaneous process starts can create different transient patterns. Some events are brief inrush currents; others are elevated loads that persist long enough to affect thermal performance or operating limits. Record the time scale, measurement method, location, and operating state alongside each value. Note whether the peak is a single event, repeats frequently, or coincides with other loads. Protection devices respond according to their characteristics and settings, so a peak should be evaluated against the complete protective-device and equipment coordination—not handled by choosing a larger continuous rating alone. Where data are uncertain, obtain appropriately time-resolved measurements or develop a documented load study. The engineer can then assess whether mitigation, sequencing, or a design adjustment is appropriate.

Provide Usable Load Information

For a project review, provide the one-line diagram, system voltage and phase, available fault-current information if known, load schedule, and the proposed equipment’s role in the distribution system. Separate steady-state current from demand readings, motor or transformer inrush, and other transient observations. For each measurement, include the date range, interval or sampling rate, instrument location, operating conditions, and whether values are RMS, instantaneous, or otherwise processed. Identify current transformers or meter settings that affect interpretation, and explain any expected future loads. If existing equipment is being replaced, supply legible nameplate and protection-device information where available; these records describe the installation but do not alone establish the correct rating for new equipment. Flag unusual duty cycles and required continuity of service. Organized, traceable inputs allow the design team to ask focused questions, compare operating scenarios, and identify missing data before equipment requirements are finalized.

Coordinate Selection, Protection, and Review

Use the continuous-current requirement to establish the appropriate equipment design basis, then evaluate transient behavior and demand peaks as separate coordination questions. The review should consider the assembly, bus and connection design, protective devices, conductors, upstream and downstream equipment, and the actual system conditions together. A peak may influence device selection or operating strategy even when it does not govern continuous current; its effect must be determined from its duration and the applicable device characteristics. Do not treat a demand meter’s maximum as a complete specification, or infer short-circuit capability from a current rating. For new switchgear, submit the project data and required performance criteria for review before procurement decisions are fixed. If schedule-sensitive options are important, raise them early; feasibility and timing depend on project scope and review. This disciplined separation helps produce a specification that reflects both sustained service and real operating events.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE