MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Close-up of tall gray switchgear cabinets with orange labels and visible breakers on wooden pallets.
AMERICAN BUILT   /   CALIFORNIA SERVED

15 kV Metal-Enclosed Switchgear

A practical framework for defining medium-voltage class, switching configuration, insulation and feeder protection for a 15 kV project.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Start with the System and Equipment Ratings

“15 kV” identifies a nominal voltage class, not a complete equipment specification. Begin by documenting the system’s nominal and maximum operating voltage, grounding method, frequency, available fault current, and expected operating conditions. Then identify the equipment’s required voltage and insulation ratings, continuous-current needs, and short-circuit withstand or interrupting duties as applicable to the selected arrangement. These values must suit the actual system and be verified against the governing project documents; a nominal class label alone cannot establish suitability. Coordinate the one-line diagram, utility information, load study, and protection study, resolving inconsistencies before design proceeds. State whether the lineup is for a new installation or a defined expansion, and identify interfaces with transformers, bus duct, cables, and existing equipment. Qualified professionals should determine protection, ratings, grounding, and applicable code requirements. This early information lets the manufacturer assess the intended duty without treating a general 15 kV description as confirmation of a particular rating.

Choose a Switching Configuration Around the Operating Plan

The switching arrangement should reflect how the facility is supplied, sectionalized, maintained, and restored after an interruption. Describe the number and function of incoming sources, bus sections, tie points, feeders, and any metering or auxiliary compartments shown on the one-line diagram. Clarify whether normal operation permits parallel sources, how transfers are controlled, and which loads require selective restoration. A main-and-tie arrangement, for example, involves different interlocking and operating considerations from a lineup with a single source and multiple outgoing feeders; neither should be selected by name alone. Explain the desired switching sequence, permissible interruption, and responsibility for operating devices. These details help identify required breakers, switches, controls, and mechanical or electrical interlocks for project review. Also account for access, cable entry, room layout, and future feeder positions, since physical constraints can affect the arrangement. Confirm each device’s intended function and ratings rather than assuming all configurations are interchangeable.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Assess Insulation and Installation Conditions

Insulation selection depends on more than nominal system voltage. Provide the specified insulation level and any required power-frequency or impulse withstand values, along with the basis used by the project engineer or governing utility. The applicable medium-voltage equipment standards and acceptance requirements must be identified for the specific equipment and application; requirements can vary with construction, installation, and jurisdiction. Do not substitute a low-voltage switchboard standard for medium-voltage equipment. Describe environmental conditions that may affect design, including indoor or outdoor placement, ambient temperature range, altitude, humidity, contamination, seismic criteria, and ventilation or enclosure constraints. Identify whether the equipment will be installed in a controlled electrical room or exposed to site conditions, and provide available room dimensions and clearances. Cable insulation, termination type, and entry direction also need coordination with the switchgear design. Treat these as project inputs to confirm, not assumed features. Qualified project professionals should establish which standards, codes, and performance criteria govern the installation.

Coordinate Feeder Protection and Control

Feeder protection must be coordinated with the connected loads, conductors, upstream supply, and downstream devices. Provide load type and magnitude, motor starting or transformer inrush information where relevant, conductor data, and available fault-current results. Identify the desired protective functions and settings basis, including any requirements for ground-fault detection, time coordination, or communications. A protection study should establish selectivity and clearing times while accounting for equipment withstand limits and the consequences of an outage. Do not treat a breaker frame or relay feature as proof that the complete protection scheme is appropriate. Indicate whether feeder devices require local or remote control, status indication, metering, alarms, or integration with a plant control or supervisory system. Document control power, communication protocols, and interface responsibilities early, since these can shape compartment layouts and wiring. Qualified engineers should select and verify protective devices and settings for the actual system; the manufacturer needs the approved design basis to evaluate the specified arrangement.

Prepare a Complete Specification Package

A focused request for quotation or design review should include the one-line diagram, equipment schedule, site conditions, required ratings, applicable standards, and project-specific specification. Show source and feeder functions, bus details, metering needs, protection intent, and interfaces to external systems. State the required quantity and lineup dimensions if established, cable entry and termination requirements, control power, and any known installation constraints. Identify which values are preliminary and which are approved, and flag open decisions so they can be resolved before release. Ask the manufacturer to review the proposed equipment rating and configuration against the documented system duty; request clarification where system data or governing criteria are incomplete. For a schedule-sensitive project, discuss possible expedited options during project review, recognizing that feasibility depends on design scope and other project factors and is not guaranteed. Switchgear Builder California builds new equipment in the USA with American components and supplies customers in California and nationwide. Provide a project contact and target milestones to support a clear, coordinated next step.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE