MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear with breakers in an industrial room, with loose conduit and fittings in the foreground.
AMERICAN BUILT   /   CALIFORNIA SERVED

Interrupting Rating

An interrupting rating states the maximum fault current a protective device is rated to interrupt at a specified voltage. Correct application requires comparing that rating with the fault current available where the device is installed.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

What an interrupting rating means

An interrupting rating is the maximum short-circuit current a protective device is rated to interrupt safely at a stated voltage and under defined test conditions. It is commonly expressed in amperes or kiloamperes. During a fault, current can rise far above normal load current; the device must open the circuit and contain the interruption without exceeding its evaluated capability. The rating is not the current the device will continuously carry, nor does it describe the system’s normal operating load. It also does not indicate how much fault current the electrical system will produce. That available fault current depends on the source, transformers, conductors, and system arrangement. In switchgear design, interrupting rating is one part of selecting and coordinating protective devices. Qualified professionals evaluate it alongside voltage, device type, system conditions, and applicable codes rather than treating a single number as a complete measure of equipment suitability.

Why the specified voltage matters

A device’s interrupting capability is tied to its rated voltage. The voltage affects the electrical energy and conditions the device must manage as contacts separate and an arc is extinguished. Therefore, a current rating stated at one voltage cannot automatically be assumed to apply unchanged at another. Consult the manufacturer’s data and markings for the applicable voltage and configuration, and verify that the device is suitable for the project’s system voltage and electrical arrangement. Pay attention to whether the system is three-phase or single-phase, grounded or ungrounded, and whether any relevant rating varies with how poles are connected. The voltage used for comparison must be the voltage that applies at the device location, not simply a nominal value copied from an unrelated project document. If procurement documents, one-line diagrams, or equipment schedules show conflicting values, resolve the discrepancy before finalizing selection. Confirming the precise voltage basis helps avoid a seemingly adequate current rating being applied outside its stated conditions.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Compare the rating with available fault current

The central application check is whether the protective device’s interrupting rating is at least the available fault current at its point of installation, at the applicable voltage. Available fault current is determined through an electrical system analysis, not by estimating from the equipment’s normal amperage. Source utility data, transformer impedance and size, conductor length and impedance, and system configuration all influence the result. Changes such as a larger transformer, shorter feeder, alternate source, or closed tie can increase the current that may reach a device. The analysis should reflect the operating configuration and assumptions required by the project. A device rating below the available fault current can be exposed to conditions beyond its interrupting capability, creating serious equipment and personnel hazards. Qualified electrical professionals determine fault-current values, assess the assumptions, and verify protective-device selection under applicable codes. If the source data or configuration is uncertain, identify that uncertainty early and have it resolved before equipment specifications are treated as final.

Distinguish interrupting rating from related ratings

Interrupting rating is related to, but distinct from, other short-circuit and equipment ratings. A circuit breaker’s interrupting rating describes its ability to interrupt a fault under stated conditions; its continuous-current rating addresses normal current carrying. An assembly’s short-circuit rating or withstand capability addresses the ability of the assembled equipment to withstand specified fault effects for defined conditions and duration. These ratings are not interchangeable, and a high interrupting rating for an individual device does not by itself establish the short-circuit capability of the complete switchgear assembly. Series-rated combinations are another special case: their use depends on tested or otherwise recognized combinations and the exact conditions permitted by applicable requirements. Do not assume that upstream protection automatically makes a downstream device suitable. Review the complete protective scheme, device combinations, and equipment ratings together. Clear terminology in specifications and submittals helps engineers, contractors, and buyers compare like with like and spot gaps before approval.

Information to confirm for switchgear selection

When preparing a switchgear inquiry or reviewing a design, provide the system voltage, phase and frequency, source and transformer details, available fault-current study, grounding method, and normal and alternate operating configurations. Include the one-line diagram, protective-device schedule, and any project requirements for coordination or selective operation. Identify where values are preliminary and who will confirm them; a device selection should not rest on an undocumented assumption about fault current. The equipment builder can use these inputs to understand the intended application and identify questions that need engineering resolution, but the project’s qualified electrical professionals remain responsible for determining protection, ratings, and code requirements. Ask for device data at the voltage applicable to the installation and verify that both individual protective devices and the assembly are addressed. For medium- or high-voltage equipment, identify and verify the standards applicable to that specific equipment. For low-voltage switchboards, determine whether UL 891 applies to the project; that standard does not establish that an assembly is listed or certified.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE