MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Several gray electrical switchgear cabinets on pallets across a spacious industrial interior.
AMERICAN BUILT   /   CALIFORNIA SERVED

Main-Lug Switchboards

Understand how upstream overcurrent protection, feeder connections, and site conditions shape a main-lug switchboard application.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

How Main-Lug Distribution Is Protected

A main-lug switchboard receives power at its incoming lugs and distributes it to outgoing circuits; it does not include a main overcurrent protective device as its incoming disconnect. Protection must therefore be provided upstream, such as by a circuit breaker or fused switch, selected for the source, conductors, equipment, and applicable code requirements. This arrangement can suit a service or distribution scheme where the upstream device is intentionally responsible for disconnecting and protecting the switchboard feeder. It also means that isolation and emergency operating procedures depend on equipment outside the switchboard. Before selecting this configuration, map the source, upstream disconnect, feeder route, and downstream loads. Qualified professionals should confirm that the upstream device’s interrupting and protective characteristics are appropriate, and that the complete arrangement supports safe operation and required access. Do not treat a main-lug design as inherently protected simply because downstream branch devices are present.

Coordinate Feeder and Overcurrent Details

The upstream protective device, feeder conductors, and switchboard must be considered as a coordinated system. Provide the source voltage and phase, available fault-current information or the basis for its calculation, upstream device type and settings, feeder conductor material and size, and the intended routing into the incoming lugs. These details help establish connection requirements and identify constraints such as conductor bending space, lug range, parallel conductors, and termination temperature ratings. Confirm how the upstream device’s trip or fuse characteristics relate to feeder ampacity and the equipment short-circuit withstand requirements; an assumed device setting can change the coordination result. If selective coordination, specific clearing times, or arc-flash objectives apply, communicate them early for engineering review rather than relying on a generic arrangement. Final protection decisions, conductor sizing, and code compliance belong to qualified professionals familiar with the project and jurisdiction.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Confirm Ratings and Applicable Standards

A main-lug switchboard’s required ratings depend on its actual electrical environment and design. Identify nominal system voltage, frequency, bus rating, number of phases and wires, neutral requirements, and the available fault current at the point of connection. The assembly’s short-circuit rating and the upstream protective device must be suitable for the installation as evaluated under applicable requirements; do not assume that a device’s interrupting rating alone establishes the rating of the complete assembly. Provide any required temperature, enclosure, environmental, or special application conditions for review. Applicable codes and standards vary with equipment type, project, and jurisdiction. For a low-voltage switchboard, determine whether UL 891 is applicable to the specified application and confirm the relevant requirements; this does not by itself establish a third-party listing. For medium- or high-voltage equipment, identify and verify the standards applicable to that specific equipment. Qualified professionals should validate all ratings and protection choices.

Plan Incoming Connections and Site Layout

Installation planning should resolve how feeder conductors enter, terminate, and reach the incoming lugs before equipment layout is finalized. Share the intended top or bottom entry, cable or busway approach, conductor count and dimensions, pull direction, and any restrictions imposed by walls, adjacent equipment, or overhead services. Check working clearances, access for termination and maintenance, door swing, equipment orientation, and the location of upstream disconnecting means against the project drawings and applicable codes. Site conditions may also affect enclosure selection and installation methods, including indoor or outdoor exposure, ambient conditions, housekeeping pads, seismic criteria, and routing through rated barriers. Where field conditions are still developing, identify assumptions and open dimensions so they can be resolved before release. A coordinated one-line diagram, elevations, and feeder schedule help the manufacturer review interfaces, while the installing contractor remains responsible for verifying actual site measurements and installation requirements.

Prepare a Clear Project Request

For a useful design review, send the one-line diagram, load schedule, equipment location, system voltage, fault-current study or available-source data, and the upstream protective device information. Include feeder conductor details, incoming orientation, required outgoing circuits, spare capacity expectations, metering or control needs, enclosure conditions, and project-specific code or coordination criteria. Flag whether the switchboard is service equipment or downstream distribution; the distinction can affect disconnecting, grounding, bonding, and labeling requirements. If the project has a constrained schedule, state the required dates and current design status so options can be reviewed, subject to engineering scope, component requirements, and project conditions. Switchgear Builder California builds new equipment in the United States with American components and supplies customers in California and nationwide, with shipping arrangements reviewed for each project. Provide a responsible engineering contact and note unresolved inputs. Clear information supports a practical proposal and helps identify decisions that must be confirmed before fabrication.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE