MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear cabinets with red circuit markings and breaker handles arranged on pallets.
AMERICAN BUILT   /   CALIFORNIA SERVED

Main-Breaker Switchgear

A single main protective device can simplify the service-entry arrangement, but its selection must work with feeder protection, available fault current and the installation’s operating needs.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

How the Main-and-Feeder Arrangement Works

Main-breaker switchgear places a primary protective device at the incoming source connection, with separate feeder protective devices serving downstream circuits. The main device provides a means to disconnect and protect the incoming portion of the assembly, while feeder devices address the circuits they supply. This arrangement creates a clear hierarchy for reviewing protection and helps operators identify the device associated with each part of the distribution system. It does not, by itself, establish that a fault will be isolated at the smallest possible point or that every device is properly coordinated. Those outcomes depend on system conditions, device characteristics and the chosen protection strategy. The design review should trace the path from the source through the main and each feeder to the connected loads. Confirm the intended function and boundaries of every protective device with the electrical engineer responsible for the project.

Select the Main Using System Inputs

Main-device selection begins with the electrical system, not a nominal frame size. Provide the nominal voltage, phase and frequency, service arrangement, source information and expected continuous load. The engineer also needs the available fault current at the equipment location, the required interrupting and withstand characteristics, and any applicable project or code constraints. A utility service, transformer or generator can affect fault-current assumptions and operating conditions; where sources can operate in parallel or transfer between one another, describe those modes as well. Consider anticipated load growth and the consequence of opening the main, including whether the facility has essential loads or operational procedures that depend on distribution continuity. The selected device and assembly ratings must be appropriate to the actual application and verified for the proposed configuration. Qualified professionals determine protection, ratings and applicable codes for each project; a product description is not a substitute for that engineering review.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Coordinate Main and Feeder Protection

A single main device does not guarantee selective coordination with downstream feeders. Coordination review compares the time-current behavior and settings of the main and feeder protective devices against the system’s available fault current and the project’s required operating objectives. The desired response may be to limit an outage to one affected feeder, but device tolerances, short-circuit conditions and the selected protection method can constrain that result. Gather the proposed device types and settings, conductor information, source and transformer data, and fault-current study results so the engineer can assess the complete path. Include relevant upstream protection and downstream equipment; reviewing the main and switchgear feeders in isolation can miss important interactions. If coordination is required by the project, identify its boundaries and documentation expectations early. The final settings and protection study should be reviewed by qualified professionals, with equipment configuration and any adjustment access aligned to the approved design.

Plan Feeder Capacity and Serviceability

The feeder section should reflect the circuits the facility must serve, not just the number of outgoing devices that fit on an initial schedule. Provide a feeder list with circuit identifiers, load descriptions, load characteristics, device requirements and any known spare or future circuits. Indicate which loads are continuous, motor-driven, sensitive, or operationally critical when that information affects the design. Space for future feeders may be useful, but reserve provisions still need a defined purpose and must be evaluated against enclosure layout, bus capacity, heat, fault duty and the applicable equipment design. Clarify cable entry direction, conductor quantities and sizes, termination preferences, available room and routing constraints. Also consider how operators will identify and access devices for inspection or maintenance. A well-developed feeder schedule and site information give the builder and project team a practical basis for resolving arrangement questions before equipment details are finalized.

Prepare a Clear Submittal and Scope Review

For a useful proposal and design review, send the one-line diagram, equipment schedule, service data, fault-current information, protection and coordination requirements, site constraints and the project schedule. Identify whether the installation is new, replacing existing equipment, or part of a broader distribution change; for replacement work, document the existing interfaces and conditions that must be verified. State the intended low-voltage or medium-voltage application rather than relying on the general term switchgear, and identify the standards and project specifications that apply to the specific equipment. UL 891 pertains to applicable low-voltage switchboards; it does not apply to every type of switchgear, and a standards reference alone does not establish a third-party listing. Review scope, ratings, interfaces and submittal expectations with the project’s qualified professionals before release. Schedule-sensitive or expedited options may be considered after project review, without assuming a particular lead time or availability.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE