MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Three tall gray electrical switchgear cabinets with open doors on wooden pallets in a large indoor space.
AMERICAN BUILT   /   CALIFORNIA SERVED

Main-Tie-Main Switchgear

Understand how main and tie devices shape source transfer, bus continuity and isolation—and what to define before specifying a main-tie-main lineup.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

How the Main-Tie-Main Arrangement Works

Main-tie-main switchgear divides a bus into sections, typically with a main device connecting each section to its source and a tie device linking the sections. The arrangement can support different operating strategies, but the hardware alone does not determine how the system behaves. The normal position of each device, the transfer sequence and the conditions that permit a tie closure must be established for the facility’s electrical design. In a common open-transition approach, a source is disconnected before the tie closes, avoiding intentional paralleling. Other strategies require careful analysis of source relationships and protection. Define which loads belong on each section, whether either source can support the combined demand, and what operating states are acceptable. These decisions affect device ratings, bus design, controls and protection coordination, so document the intended sequence before requesting a lineup.

Choose the Operating Mode Around the Load

Operating modes balance continuity, simplicity and the available capacity of each source. With both mains normally closed and the tie open, each source serves its own bus section; this can limit the extent of an outage, but does not automatically provide backup if a source fails. A normally open tie can allow one source to supply both sections after a planned or abnormal transfer, only when the source and equipment are suitable for the resulting load. A different normal state may suit a facility’s operations, yet can change fault-current exposure and protection requirements. Consider essential and nonessential loads, motor starting, demand peaks, generator or utility limitations, and whether transfer is manual or controlled automatically. Also decide whether loads may be shed before transfer. Qualified electrical professionals should evaluate system studies and operating procedures; switchgear selection should follow those project-specific findings rather than assume a universally preferred mode.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Define Interlocks and Transfer Conditions

Source interlocks help prevent prohibited device combinations, but the required logic must be specified rather than inferred from the phrase main-tie-main. For an open-transition scheme, the control sequence may require confirmation that a main is open before the tie can close, and that the tie is open before a disconnected source is reconnected. Specify whether interlocking is mechanical, electrical, key-based, or a coordinated combination, along with the intended behavior during loss of control power or an abnormal device indication. If closed-transition transfer or any source paralleling is contemplated, identify that explicitly; it introduces additional synchronization, protection, utility and operating considerations and must not be treated as an ordinary tie operation. State which devices initiate transfer, what conditions inhibit it, whether operators can override controls, and how alarms and status are presented. The engineer of record should validate the sequence against the one-line diagram, protection scheme and applicable requirements.

Plan Bus-Section Isolation and Maintenance

The tie device provides a controlled connection between bus sections; opening it can separate the sections for operation or troubleshooting, but it does not by itself establish a safe work condition. Isolation boundaries, disconnecting means, grounding provisions where required, and procedures for verifying absence of voltage must be determined for the actual equipment and applicable rules. Consider how a fault or maintenance activity on one section affects the other section, including shared control circuits, instrument transformers, auxiliary power and cable routing. Physical barriers and compartment arrangements also influence access, serviceability and the risk of disturbing energized equipment. Define whether each section must remain available while the other is isolated, and identify any loads that cannot tolerate interruption during that work. Qualified personnel must apply project safety procedures and confirm all sources and possible backfeeds before work. Clear device labels and an accurate operating sequence help translate the design intent into safe day-to-day practice.

Prepare a Project-Ready Specification

A useful request for main-tie-main switchgear includes a one-line diagram, system voltage and frequency, source details, available fault-current information, load data, and the intended normal and emergency device positions. Identify whether sources are utility, generator or another arrangement, and provide any restrictions on paralleling or transfer. Include required continuous-current and interrupting or withstand ratings as design inputs for confirmation, not assumptions based on the topology. Note metering, relaying, control power, communications, enclosure environment, cable entry, space limits and future expansion needs. List applicable codes and standards for the specific equipment; UL 891 relates to applicable low-voltage switchboards and does not establish a listing or apply to every voltage class. For medium- or high-voltage equipment, identify and verify standards appropriate to that equipment. Switchgear Builder California builds new equipment in the USA with American components. Share project documents and schedule constraints for review; any expedited approach depends on scope and confirmation.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE