MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Several gray electrical switchgear cabinets on pallets across a spacious industrial interior.
AMERICAN BUILT   /   CALIFORNIA SERVED

Selective Coordination Requirements

A practical framework for reviewing coordination objectives and device curves before switchgear design is finalized.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Define the Coordination Objective

Selective coordination aims to isolate a fault as close to its source as practicable while keeping unaffected portions of the distribution system energized. Before reviewing devices, establish which circuits and loads must remain in service, what interruption boundaries the project requires, and which operating conditions matter. Requirements may come from the owner’s continuity goals, project specifications, applicable codes, or the authority having jurisdiction; qualified professionals must determine what applies. A broad request to “coordinate the system” is not enough to evaluate performance. Identify the relevant upstream and downstream protective devices, including alternate sources, tie breakers, generator connections, and bypass paths where present. Record whether the study must address normal and emergency configurations. These decisions define the scope of curve review and help avoid a design that appears coordinated on one-line diagrams but behaves differently after a transfer or switching change.

Assemble the Inputs Behind the Curves

Time-current curves are only useful when their underlying inputs reflect the actual system. Gather the one-line diagram, transformer and source data, conductor and grounding information, anticipated short-circuit current, and device manufacturer, catalog number, sensor or rating plug, trip unit, and settings. Include current-limiting fuses, relays, motor protection, and other devices that influence the protective chain. Confirm available fault current at each relevant point for every source arrangement; utility contributions, generator decrement, and transformer impedance can change the result. If equipment or settings are not yet selected, label assumptions clearly and identify who will resolve them. Distinguish nominal values from verified data, and flag missing information instead of treating estimates as final. A coordinated curve set depends on consistent system voltage, frequency, equipment tolerances, and device characteristics, as well as accurate scaling and calculation methods.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Compare Curves Across Operating Conditions

Review each downstream device against the next upstream protective device over the fault-current range that matters, not just at one plotted point. Compare instantaneous, short-time, and long-time pickup and delay regions where applicable, along with ground-fault functions and fuse characteristics. Check both minimum and maximum fault current: a high-current event may enter an instantaneous region, while a lower-level fault may clear in a delayed portion of the curves. Account for tolerances, trip-unit bands, relay operating times, and breaker clearing time, not merely nominal pickup settings. Coordination margin must be evaluated using the applicable device data and the project’s acceptance criteria. Repeat the review for alternate source and tie configurations, since available fault current and protection paths can differ. A visual gap on a graph is not by itself proof of selective coordination; verify the actual limits and assumptions with the responsible protection engineer.

Resolve Selectivity and Protection Tradeoffs

Improving selectivity can require longer upstream delays, adjusted pickup values, or different device characteristics. Those choices must be balanced against conductor and equipment protection, arc-flash exposure, interruption capability, and the need to clear faults promptly. Do not raise settings solely to separate curves without checking the resulting protection at minimum fault levels and the withstand limits of downstream equipment. Where curves overlap, determine whether the conflict is real under the required conditions, and whether a different device, trip unit, fuse, zone-selective interlocking scheme, or system arrangement merits evaluation. Any proposed change should be reviewed across all affected feeders and source modes, not in isolation. Protection settings and arc-flash outcomes are related but distinct engineering questions; one should not be treated as a substitute for the other. Qualified professionals should approve final protection, ratings, and code decisions for the installation.

Document Decisions for Equipment Design

A useful coordination package makes the design review traceable. Provide the latest one-line, load and source data, short-circuit study, device schedule, proposed settings, curve plots, assumptions, and a concise list of exceptions or unresolved items. Identify which operating configurations were studied and show the upstream-downstream relationships that support each conclusion. For switchgear procurement, share the required voltage, continuous-current and interrupting requirements, bus arrangement, incoming and tie scheme, protective-device preferences, control interfaces, and project standards. Treat these as design inputs to confirm, not as evidence that a particular rating or configuration is available. Align the study revision with equipment submittals and construction changes; a transformer, breaker, or settings substitution can invalidate earlier conclusions. Ask the manufacturer to review relevant interface and device information during design coordination, then have the project’s protection professional validate final settings and field conditions before operation.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE