MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
A long row of gray Allen-Bradley control cabinets with black switch handles on pallets indoors.
AMERICAN BUILT   /   CALIFORNIA SERVED

Current and Voltage Transformer Ratings

A practical guide to specifying current and voltage transformers for dependable metering and protection performance.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Start With the Circuit and Application

Instrument transformer selection begins with the electrical system and the task the transformer must perform. For a current transformer (CT), document the nominal and maximum primary current, system voltage, frequency, fault-current conditions and the conductor or bus arrangement. For a voltage transformer (VT), identify the primary system voltage, grounding method, phase configuration and the secondary voltage required by the connected devices. Distinguish revenue or operational metering from protective relaying: each can place different demands on ratio, accuracy and performance during abnormal conditions. Record whether the application is single-phase or three-phase and how secondary circuits will be connected. These details help establish a suitable ratio and avoid treating a familiar ratio as automatically appropriate. Provide one-line diagrams, equipment drawings and relay or meter information when requesting a design review. Qualified professionals should confirm system studies, protection requirements and applicable codes for the specific project.

Choose Ratios for Real Operating Conditions

A CT ratio should reflect expected operating current, not simply the switchgear's nominal bus rating. If the primary rating is much higher than normal load, the secondary signal may use only a small portion of the instrument's range, affecting useful measurement resolution. Conversely, a ratio selected too close to ordinary load may leave inadequate headroom for changing demand or overload conditions. Consider normal, peak and anticipated future load, as well as the input range and scaling supported by meters and relays. Specify the intended secondary current and confirm compatibility with every connected device. For VTs, relate the primary-to-secondary ratio to system voltage, phase arrangement, grounding and device input requirements; identify any required connection or residual-voltage measurement scheme. Ratios should also be coordinated with control diagrams and settings so displayed values, relay quantities and drawings agree. State design assumptions explicitly, especially where load growth, operating modes or system configuration may change.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Account for Burden and Connected Devices

Burden is the electrical load imposed on an instrument transformer's secondary circuit, commonly expressed in volt-amperes at a stated power factor. It includes the connected meters, relays and other devices, plus wiring and terminal effects. For CT circuits, long or undersized secondary leads can add resistance and burden, influencing accuracy and behavior during fault conditions. For VT circuits, lead length, conductor size, fuses and the connected inputs likewise affect the circuit. Gather device input data, lead distances, conductor sizes and the number of connected instruments before selecting a burden requirement. Do not assume that every device listed on a drawing is connected to the same transformer winding; verify the actual circuit arrangement and any separate metering or protection cores. Compare the calculated burden with the transformer's specified performance at the required conditions. If the design changes, recalculate rather than relying on an earlier estimate. The project team should resolve unclear device data before drawings and settings are finalized.

Match Accuracy and Protection Performance

Accuracy requirements depend on whether measurements support billing, operational monitoring, control or protective relaying. Specify the relevant accuracy class or performance criteria using the governing project documents and applicable standards, then confirm that the proposed transformer can meet the intended duty across its operating range. CTs used for protection may need to reproduce current acceptably during high-current fault events, while metering CTs are selected for useful accuracy under expected load conditions. These objectives can differ, so separate cores or dedicated transformers may be considered when the circuit design and equipment arrangement support them. VT accuracy and voltage behavior should be considered alongside the relay or meter functions, including any required residual or phase quantities. Confirm device compatibility, polarity, terminal identification and wiring diagrams as part of the review. A ratio or accuracy designation alone does not establish complete protective coordination: qualified professionals must evaluate fault studies, relay settings and the full protection scheme.

Verify Insulation, Installation and Documentation

Insulation selection must correspond to the system's voltage class, grounding conditions, installation environment and the equipment in which the transformer will be installed. Identify required insulation levels and clearances as design inputs for review; do not substitute a nominal system voltage for the applicable withstand requirements. Consider temperature, contamination, altitude, enclosure conditions and any project-specific environmental demands. For medium- or high-voltage equipment, identify and verify the standards applicable to that specific equipment and application. UL 891 applies to applicable low-voltage switchboards, not to medium- or high-voltage equipment or every instrument transformer. Before release, check that ratios, secondary ratings, burden, accuracy requirements, insulation data, connection diagrams and physical interfaces are consistent across the one-line, schematics and equipment documents. Provide the intended switchgear arrangement, device data and project specifications so requirements can be reviewed. Any unresolved rating, code or protection question should be addressed by qualified professionals before equipment design is finalized.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE