MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear beneath overhead conduits in an industrial room, with gallery arrows overlaid on the image.
AMERICAN BUILT   /   CALIFORNIA SERVED

800 Amp Service-Entrance Switchboards

Evaluate the service connection, main disconnect, metering arrangement and downstream distribution as coordinated design inputs for an 800 A switchboard.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Start with the utility service interface

An 800 A service-entrance switchboard must be planned around the serving utility’s requirements as well as the building’s electrical demand. Confirm the service voltage, phase, frequency, available fault current, grounding arrangement and point of connection with the utility and project engineer. Utility rules may govern service conductors, termination space, sealing provisions, metering location and access clearances; these details can affect the enclosure layout and equipment arrangement. Clarify responsibility for service conductors and terminations, and identify any utility-furnished metering components or approved interfaces before design is finalized. An 800 A nominal service designation does not by itself establish the short-circuit rating, bus rating or suitability for a particular service condition. Provide one-line diagrams, utility correspondence and site constraints early so those requirements can be reviewed together. Final service configuration and applicable code requirements should be determined by qualified electrical professionals in coordination with the utility.

Coordinate the main disconnect and protection

The main disconnect is central to service isolation and protection, but its selection depends on more than the 800 A service value. The design team should establish the required device type, continuous-current rating, interrupting capability, trip characteristics and any ground-fault protection requirements based on the installation and governing rules. Available fault current at the equipment is especially important: the assembly’s short-circuit withstand or interrupting ratings must be evaluated separately from its nominal ampere rating. Coordinate the main device with upstream utility protection and downstream feeder devices to support selective operation where required, while recognizing that coordination can be limited by device characteristics and fault levels. Include equipment grounding and bonding details, neutral treatment and service disconnect identification in the design review. Qualified professionals must determine the protection scheme, ratings and code compliance for the specific project; the service-entrance designation alone does not establish these outcomes.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Resolve metering and service-access details

Metering interfaces can drive both the electrical arrangement and the physical dimensions of an 800 A service-entrance switchboard. Determine whether the utility requires a particular meter location, instrument-transformer arrangement, compartment separation, test provisions or access method. Confirm who supplies current transformers, meters, wiring and related hardware, and whether utility review is required before fabrication. The project should also document working space, door swing, approach and maintenance access, conductor bending space, conduit entry locations and any restrictions imposed by the electrical room. These practical constraints matter in tenant spaces and retrofit projects, where existing walls, structural members and adjacent equipment may limit available footprint. Share dimensioned plans, elevations, conduit schedules and the latest utility metering criteria with the equipment supplier. Resolve conflicts among access, metering and cable routing before release; late changes can affect the arrangement, interfaces and installation coordination.

Plan commercial distribution and future load

For commercial distribution, develop a feeder schedule that reflects present loads, expected operating patterns and the function of each downstream circuit. Identify breaker or fusible-device requirements, feeder quantities, conductor sizes, connected loads and any critical or emergency loads that influence distribution. Future allowance should be deliberate: spare spaces, provisions for additional devices and capacity margin are different considerations, and none should be assumed from an 800 A label. Estimate likely load growth and reserve practical room for planned additions, while checking that bus, overcurrent devices, conductors and service capacity remain appropriate as the system evolves. Review motor starting, nonlinear loads, power factor correction and other characteristics that may affect demand or protection. A clear one-line diagram and load calculation help the design team distinguish current requirements from future intent. Have qualified professionals verify demand, code obligations and the effect of any planned expansion.

Verify ratings and prepare the design package

Treat the 800 A configuration as a starting point, then verify each rating and interface independently. Bus ampacity, main and feeder device ratings, voltage class, available-fault-current capability, environmental suitability and enclosure requirements are separate design questions. Do not assume that one rating establishes another, or that a service-entrance application determines a particular construction or approval. Applicable standards depend on equipment type and project conditions; for low-voltage switchboards, UL 891 may apply where relevant, but any listing or approval status must be confirmed for the specific assembly rather than inferred from a standard reference. For medium- or high-voltage equipment, identify and verify the standards applicable to that equipment. To support a design review, provide the utility service requirements, one-line diagram, load data, fault-current information, metering criteria, site dimensions and requested options. Switchgear Builder California builds new equipment in the USA with American components and supplies customers in California and nationwide. Schedule-sensitive options, if considered, are subject to project review.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE