MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Close-up of tall gray switchgear cabinets with orange labels and visible breakers on wooden pallets.
AMERICAN BUILT   /   CALIFORNIA SERVED

347/600 Volt Motor Control Centers

Use system details, motor data, and protection requirements to confirm whether a proposed motor control center fits a 347/600 V project.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Confirm the 600 V System and Equipment Rating

The notation 347/600 V commonly describes a grounded-wye system with 600 V phase-to-phase and 347 V phase-to-neutral. That distinction matters when defining the motor control center’s incoming supply, control circuits, and connected loads. Begin with the project’s one-line diagram and confirm the nominal voltage, frequency, grounding method, available fault current, and any expected operating variations. Do not treat a 600 V system label as proof that a particular assembly or component has the required rating. The equipment rating must be verified against the system conditions and project requirements. Identify whether the lineup serves only three-phase motors or also supplies line-to-neutral loads, and document how those loads are distributed. Qualified professionals should establish protection, installation, and code requirements for the application. Clear system information helps the manufacturer evaluate the design and reduces uncertainty before equipment configuration is finalized.

Match Starters and Drives to Motor Data

Motor starter and drive selection should follow the actual motor nameplate and operating duty, not voltage alone. Provide each motor’s horsepower or kilowatt rating, full-load current, service factor where applicable, starting method, load characteristics, and expected starts per hour. Note whether motors operate continuously, cycle frequently, reverse, or face demanding acceleration or braking conditions. For variable frequency drives, identify the required speed range, control method, enclosure and environmental constraints, and any interaction with upstream protection or downstream motor cables. Drive input and output ratings, overload capability, and compatibility with the motor and application all require confirmation. Also identify bypass requirements, if considered, and explain how the process should behave during a drive fault or maintenance condition. A conventional starter and a drive can serve different operating goals; comparing energy control, process needs, maintenance, and complexity helps select the appropriate approach for each motor.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Define Control Power and Interface Needs

Control power deserves a separate review because the 347/600 V distribution system does not by itself establish how control circuits should be supplied. Specify the preferred control voltage and source, whether control power should be centralized or arranged by unit, and the loads served by each control circuit. Identify required transformers or other power-supply arrangements as design inputs for review, rather than assuming a particular configuration is included. List field devices, permissives, interlocks, local and remote commands, status points, alarms, and communications interfaces. Where a supervisory system is involved, provide its protocol and signal requirements and clarify which party furnishes or terminates field wiring. Describe fail-safe expectations for loss of control power and the intended response to emergency-stop or process-trip signals. Consistent control documentation helps coordinate the motor control center with process controls, instrumentation, and upstream systems, while reducing commissioning questions about responsibility and point-to-point behavior.

Coordinate Feeder Protection and Fault Conditions

Feeder protection should be evaluated together with motor branch-circuit protection, the upstream source, and the project’s coordination objectives. Provide the available fault current at the equipment location, upstream protective-device information, transformer data where relevant, and any study results or design criteria already established. The responsible engineer can use this information to evaluate interrupting and withstand requirements, protective-device selection, and coordination with downstream loads. Identify whether selective coordination, arc-flash considerations, or continuity-of-service goals influence the design; these objectives can involve tradeoffs in protection and operating behavior. State how spare or future feeders should be treated, since reserved space does not establish a future circuit’s rating or protection. Confirm applicable electrical codes and standards for the specific equipment and installation. Qualified professionals determine protection settings and safe work practices. Supplying current project documents early supports a focused review and helps uncover mismatches before procurement and field integration.

Prepare a Project Package for Review

A useful inquiry package combines the one-line diagram, load schedule, motor list, control narrative, site conditions, and required delivery or installation constraints. Include enclosure location, ambient conditions, elevation if relevant, cable-entry preferences, lineup dimensions or space limits, and any interface with existing distribution equipment. Clarify project-specific documentation, testing, labeling, and submittal needs, while treating every rating and requirement as subject to engineering review. The 347/600 V equipment market and component availability can vary by application and timing, so identify acceptable alternatives and any components that must be maintained for standardization. If schedule is sensitive, provide the required dates and decision milestones; expedited options, if considered, depend on project review and confirmed scope. Switchgear Builder California builds new equipment in the USA with American components and supplies customers in California and nationwide. A complete package gives the manufacturer a practical basis to assess fit, clarify open items, and develop a project-specific proposal.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE