Start with the system voltage and equipment class
A 27 kV project designation is a starting point, not a complete equipment specification. Confirm the system’s nominal distribution voltage, maximum operating voltage, grounding method, frequency and expected operating conditions. These values establish the context for selecting equipment class and checking whether the assembly’s applicable voltage rating fits the system. Do not treat a nominal voltage label as proof that a particular rating is suitable. The engineer of record should reconcile the utility or facility design basis, one-line diagram and equipment requirements, including any future operating scenarios that affect voltage or fault exposure. Identify whether the installation is indoor or outdoor and document ambient temperature, altitude, contamination, moisture and available space. Such conditions can influence insulation selection, enclosure design and clearances. When requesting a proposal, provide the governing drawings and project criteria, and ask that the proposed equipment rating and assumptions be stated clearly for engineering review.
Coordinate insulation with system conditions
Insulation requirements must be evaluated in relation to the system, not selected from the nominal voltage alone. Define the required power-frequency withstand and impulse withstand levels where applicable, then confirm the values against the standards and project criteria governing the specific medium-voltage equipment. Insulation coordination should account for overvoltage sources, grounding behavior, protective devices and the exposure of connected cable and apparatus. Surge arresters, for example, must be selected and located with system grounding and insulation levels in view; their presence does not eliminate the need to verify switchgear withstand requirements. Environmental conditions can also affect insulation performance, especially where altitude, pollution or condensation differs from ordinary indoor service assumptions. Document those conditions early so that equipment details and clearances can be reviewed coherently. For a 27 kV application, request explicit confirmation of the applicable equipment class and insulation requirements rather than assuming that a voltage designation alone establishes either one.
| System | Voltage, phase, current and available fault current |
|---|---|
| Configuration | Lineup, protection, controls and enclosure as specified |
| Compliance | Applicable standards and listing confirmed for the assembly |
| Delivery | California and nationwide; schedule confirmed by quote |
Define switching by operating purpose
Specify switching functions according to what the system must do during normal operation, maintenance and abnormal conditions. Identify incoming sources, bus sections, tie points, transformer connections and outgoing feeders, then show which devices must isolate, interrupt load or fault current, or support transfer between sources. A one-line diagram is essential, but operating sequences and interlocking expectations often need separate explanation. Clarify whether source transfer is manual or automatic, which loads may be interrupted, and what conditions should block a switching action. The chosen arrangement affects equipment layout, operating access, control wiring and coordination with upstream and downstream devices. Avoid describing a general preference as a confirmed product configuration; instead, state functional requirements and ask the manufacturer to review the proposed arrangement. Include maintenance and isolation procedures in the design discussion. Qualified professionals must determine safe work practices and switching procedures for the installation; equipment selection alone does not establish a safe operating plan.
Develop feeder protection from the fault study
Feeder protection begins with dependable system data. Provide available fault current at the switchgear, source and transformer impedances, grounding details, conductor information, connected loads and relevant upstream protection settings. For each feeder, identify the protected equipment, expected load, starting or inrush behavior, and any selectivity or coordination objectives. The protection engineer can then evaluate device ratings, sensing and trip functions, time-current coordination, ground-fault response where applicable, and the effect of changing operating configurations. A device’s interrupting capability must be checked against the available fault current at its point of application; nominal voltage or feeder ampacity does not answer that question. Consider how relay settings and control power will be documented, tested and maintained. Provide the latest short-circuit and coordination studies when available, and flag assumptions that remain open. Qualified professionals determine protection settings and applicable code requirements for each project, with final selections verified against the actual system.
Submit a reviewable specification package
A clear request for 27 kV metal-enclosed switchgear should combine the electrical basis with practical installation and procurement details. Include the one-line diagram, equipment schedule, site conditions, cable entry and termination requirements, control schematics or functional descriptions, communications needs, and the project’s required standards. Identify the intended equipment location, access constraints, working clearances and interface points with other packages. State required ratings as design inputs for confirmation, including continuous current, short-circuit duty, insulation levels and any applicable switching duties. For medium-voltage equipment, identify and verify the standards applicable to the specific assembly; requirements vary with equipment design and use. Review proposed deviations, exclusions and open data items before releasing the design for construction. If the project schedule is sensitive, share milestone dates and decision deadlines early so potential schedule-sensitive options can be reviewed; timing depends on project scope and confirmation. Switchgear Builder California builds new equipment in the USA with American components and serves California customers and projects nationwide, with shipping subject to project review. Request a specification review using the project documents.
