MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Electrical cabinets secured on a flatbed truck in an outdoor lot beneath a blue sky.
AMERICAN BUILT   /   CALIFORNIA SERVED

120/240 Volt Switchboards

Start with the system—not the voltage label. Compare the source, conductor arrangement, device ratings, and bus configuration before defining a 120/240 V switchboard.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Identify the 120/240 V system

A 120/240 V designation does not, by itself, define the switchboard’s phase or conductor arrangement. A common split-phase service has two ungrounded conductors and a grounded conductor, with 120 V available from either ungrounded conductor to neutral and 240 V across the two ungrounded conductors. A 120/240 V three-phase, four-wire delta system is different: it has three phase conductors and a neutral, and the phase-to-neutral voltages are not all 120 V. Confirm which system serves the project rather than treating the nominal voltage as a complete specification. Review utility or transformer documentation, one-line diagrams, grounding details, and the intended loads with the electrical design team. This distinction affects device selection, bus arrangement, phase identification, and how circuits are distributed. If the available documentation is incomplete or inconsistent, resolve the source configuration before requesting a final equipment design.

Match main and feeder device ratings

Specify the main and each feeder device against the actual system and its connection, not just the largest number printed on the panel schedule. Verify the device’s voltage rating, pole configuration, and intended application against the equipment rating and the circuit it protects. A 240 V line-to-line load and a 120 V line-to-neutral load do not use conductors in the same way; where a neutral is required, confirm how it is routed and terminated. On a three-phase delta system, identify whether any phase-to-neutral loads are connected and how the system’s voltage relationships affect device application. Do not assume that a breaker’s nominal voltage or pole count alone establishes suitability. Provide the proposed main and feeder schedule, load descriptions, and any special switching or isolation requirements for review. Qualified professionals must determine protection, interrupting capability, and code compliance from the available fault-current data and project conditions.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Define bus and conductor arrangement

The bus arrangement should reflect the source conductors and the intended distribution—not a generic interpretation of “120/240.” For split-phase service, clarify the two ungrounded bus legs, neutral requirements, and how single-pole and two-pole feeders will be assigned. For a three-phase, four-wire arrangement, identify all three phases and the neutral, and indicate how loads are distributed across them. This information helps expose phase-balance issues and prevents an assumed arrangement from being carried into drawings or fabrication. State whether the project expects a particular bus sequence, phase identification convention, neutral treatment, or space for future circuits. Include conductor material preferences or project requirements if applicable, while treating bus material and dimensions as design details to confirm for the required rating. The one-line, schedules, and equipment notes should agree. When they do not, document the discrepancy and obtain direction from the engineer of record before the configuration is finalized.

Confirm the applicable equipment rating

The required equipment rating depends on more than nominal system voltage. Identify the service or feeder conditions, continuous and noncontinuous loads, available fault current, environmental conditions, and any project-specific performance requirements. Check that the proposed switchboard rating and the ratings of its main and feeder devices are appropriate for those conditions, including the intended system grounding and conductor arrangement. Provide the source transformer information or utility fault-current data when available; if values are not yet established, mark them as pending rather than substituting an unsupported assumption. Also clarify whether the equipment is service entrance equipment or downstream distribution, since that distinction can affect design and protection requirements. Applicable standards and code provisions must be determined for the specific equipment and installation. Qualified professionals should verify ratings, protection coordination, and code requirements; a nominal voltage match alone does not establish suitability or approval.

Prepare a complete specification package

A useful request for a 120/240 V switchboard includes the one-line diagram, system type, number of phases and wires, source and grounding details, and a schedule of mains, feeders, and connected loads. Add available fault-current information, the intended equipment location, environmental constraints, access or space limits, and any required future capacity. Clearly flag assumptions and unresolved items so they can be reviewed instead of silently built into the design. For California projects or work elsewhere in the United States, identify the governing project documents and the professionals responsible for confirming applicable requirements. Switchgear Builder California builds new switchgear in the USA with American components and supplies equipment to customers; project requirements are reviewed to establish an appropriate scope. Nationwide shipping may be considered based on project review. If schedule is a constraint, share the required dates and decision milestones early; any schedule-sensitive or expedited possibility depends on project details and review, not a guaranteed delivery date.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE