MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear with breakers in an industrial room, with loose conduit and fittings in the foreground.
AMERICAN BUILT   /   CALIFORNIA SERVED

120/240 Volt Panelboards

Align the panelboard specification with the actual 120/240 V system: confirm phase and conductor arrangement, map branch circuits, and verify ratings before equipment selection.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Identify the 120/240 V System

A 120/240 V designation alone does not establish the panelboard’s phase arrangement or conductor configuration. Many installations use a single-phase, three-wire split-phase system: two ungrounded conductors and a grounded neutral, with 120 V available from either line to neutral and 240 V line to line. Other projects may involve a three-phase system with 120/240 V characteristics, such as a four-wire delta arrangement with a high leg. These are not interchangeable configurations, and their conductor assignments, voltage relationships, and connected-load implications differ. Start with the service or feeder documentation and confirm the actual system with the electrical engineer or utility as appropriate. State phase, number of wires, nominal voltages, grounding arrangement, and any high-leg identification requirements in the equipment specification. If the installation is existing, verify field conditions rather than relying solely on an old panel schedule. Clear configuration data prevents incorrect assumptions about breaker positions, neutral use, and circuit balancing.

Specify Branch Breakers by Load

Branch breaker selection should follow the connected load and the applicable design rules, not simply the panelboard’s voltage label. For every circuit, identify the load type, expected current, poles required, and any equipment-specific instructions; also note whether the circuit is continuous or has starting, inrush, or other operating characteristics that affect protection. A 120 V line-to-neutral branch generally uses one pole, while a 240 V line-to-line load typically requires a two-pole device. Three-phase loads and high-leg systems require careful phase identification so a branch is supplied at the intended voltage. Record the required breaker frame or trip characteristics only when established by the design, and identify any special functions, such as ground-fault or arc-fault protection, where applicable. Confirm compatibility between the specified breaker and the panelboard design. Qualified professionals must determine overcurrent protection and applicable code requirements for each installation; do not treat a breaker rating as a substitute for a load calculation.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Build a Circuit Layout That Works

A useful circuit schedule connects each breaker position to a real load, location, voltage, and phase assignment. For split-phase service, distribute 120 V loads between the two line conductors with the design’s calculated demand in mind, while reserving paired positions for required two-pole 240 V circuits. In a three-phase arrangement, identify the phase sequence and assign single-phase loads to the intended phase pairs; do not assume that a familiar split-phase position pattern applies. Note spare spaces separately from spare capacity: an unused position does not establish that the bus or feeder can support future load. Include planned additions, dedicated equipment circuits, and loads that may require future expansion. The final schedule should be legible to installers and maintenance personnel, with consistent circuit numbering and clear descriptions. Reviewing this layout before fabrication helps expose conflicts such as too few two-pole positions, an unsuitable phase balance, or insufficient room for anticipated circuits.

Verify Equipment and Interrupting Ratings

Specify the ratings that govern the complete application, rather than assuming that a 120/240 V label answers every selection question. Confirm nominal system voltage, frequency where relevant, bus and feeder current requirements, and the available fault current at the equipment location. The selected panelboard and its protective devices must have suitable voltage and interrupting ratings for the installation; any series-rated approach, if considered, requires verification against the exact equipment combinations and applicable requirements. Check enclosure and environmental needs, mounting arrangement, incoming conductor provisions, and the neutral and grounding details. For three-phase, four-wire delta service, explicitly identify the high leg and require it to be handled and marked according to the design and applicable rules. Provide the available fault-current study or the responsible party’s confirmed value, along with upstream protective-device information. Qualified professionals should determine protection, ratings, and code compliance; the equipment specification should make each decision reviewable.

Prepare the Specification for Review

A complete inquiry helps the manufacturer assess the intended panelboard without relying on assumptions. Provide the one-line diagram, service or feeder details, phase and conductor arrangement, voltage, load data, fault-current information, and a current circuit schedule. Identify the required breaker quantities and poles, anticipated spare positions, enclosure and installation conditions, and any project-specific marking or documentation needs. Flag unresolved items—particularly whether the source is split-phase or three-phase—so the electrical engineer can confirm them before equipment details are finalized. Compare the proposed arrangement with upstream protection, downstream equipment, available space, and the installation’s coordination requirements. For low-voltage switchboards, UL 891 applies where relevant, but it does not establish a listing for any particular assembly; confirm the standards and any listing requirements applicable to the specified equipment. Switchgear Builder California builds new equipment in the USA with American components. Customers can submit project requirements for review, including schedule-sensitive requests, which are evaluated for feasibility rather than assumed timing.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE