MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Three tall gray electrical switchgear cabinets with open doors on wooden pallets in a large indoor space.
AMERICAN BUILT   /   CALIFORNIA SERVED

120/240 Volt Automatic Transfer Switches

A practical specification guide to matching a 120/240-volt automatic transfer switch to the electrical system, sources and transfer requirements.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Identify the System Before Choosing an ATS

The label “120/240 volts” does not by itself define the source arrangement or establish that two sources are compatible. A common configuration is single-phase, three-wire split-phase service, with two ungrounded conductors and a neutral. Each ungrounded conductor measures approximately 120 volts to neutral, while the voltage between them is approximately 240 volts. Other systems can present different phase relationships and conductor arrangements. Start by documenting the normal and alternate source voltages, phase, frequency, grounding method and available conductors from reliable project documents, then have qualified professionals confirm them at the design stage. Check whether the alternate source is a generator or another utility source, and whether its output and neutral arrangement match the loads and transfer scheme. A nominal voltage match is not sufficient: incompatible phase, grounding or neutral conditions can create incorrect operation or unsafe current paths. Resolve discrepancies between one-line diagrams, equipment schedules and field information before selecting equipment.

Distinguish Split-Phase From Three-Phase Arrangements

A split-phase 120/240 V supply is not interchangeable with a three-phase system simply because a drawing or schedule includes both 120 V and 240 V values. A three-phase, four-wire wye source may provide 120 V line-to-neutral and 208 V line-to-line; a different three-phase arrangement may have different voltage relationships and grounding characteristics. Confirm the actual system configuration rather than inferring it from one measured voltage or a generic “120/240” description. Identify every source conductor, including whether a neutral is present and how it is grounded. If a project has multiple source types, document each independently and establish what voltage and phase the transferred load requires. The ATS must be selected and configured for the system it will serve, not for a shorthand voltage description. Ask the electrical designer to reconcile conductor counts and phase designations across the one-line, riser and generator information. This early check helps prevent mismatched equipment, costly drawing revisions and commissioning delays.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Specify Poles and Neutral Treatment Deliberately

Pole configuration depends on which conductors must be switched and on the system grounding and neutral arrangement; it should not be chosen solely from the nominal voltage. For a split-phase system, the two ungrounded conductors are normally part of the transfer path. Whether the neutral is switched is a separate design decision that depends on the source bonding and grounding scheme, applicable codes and the intended transfer arrangement. A switched-neutral design and a solid-neutral design have different implications for grounding continuity and source isolation. Provide the ATS manufacturer or builder with a one-line diagram showing source conductors, neutral and equipment-grounding conductors, and indicate how each source is bonded. Do not treat the equipment-grounding conductor as a switching pole. For three-phase applications, specify phase count and identify whether the neutral is included, rather than carrying over a split-phase assumption. Qualified professionals must determine the appropriate pole arrangement and verify it against the project’s grounding design and applicable requirements.

Define Transfer Controls and Operating Priorities

Transfer controls should reflect how the facility expects the alternate source to start, qualify and assume load. Specify whether transfer is open transition, where the load is disconnected from one source before connection to the other, or whether another transfer approach is required and supported by the project design. Describe the normal-source failure criteria, acceptable voltage and frequency ranges, time delays, retransfer preference and generator cooldown sequence as design requirements for review. Include any need for manual operation, remote status, alarms or interfaces with a generator controller or building management system. Identify loads that cannot tolerate interruption and determine whether they need separate continuity measures; an ATS does not eliminate the transfer interval. Control features and settings must be coordinated with source behavior and load requirements, not selected as generic defaults. Give the project team a clear sequence of operation and control-interface details so the proposed arrangement can be evaluated before procurement and checked during commissioning.

Confirm Ratings and Submit a Complete Basis

Verify the applicable equipment rating against the installation and load, including system voltage, continuous current, available fault current and the required short-circuit or withstand performance. Confirm the enclosure and environmental conditions, installation location, cable entry, terminals and any project-specific control or accessory requirements. These values are design inputs to confirm for the proposed equipment; a 120/240 V designation alone does not establish suitability. Provide the one-line diagram, source data, load schedule, grounding details, protection information and sequence of operation with the specification request. Identify the governing codes and standards applicable to the particular equipment and installation; qualified professionals should determine protection, ratings and code requirements for each project. For any equipment standard or approval requirement, verify its applicability to the equipment type and project, and do not equate a design standard with third-party listing. A complete submittal basis lets the manufacturer review compatibility, clarify open items and support a more reliable procurement and commissioning process.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE