MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Several gray electrical switchgear cabinets on pallets across a spacious industrial interior.
AMERICAN BUILT   /   CALIFORNIA SERVED

Arc-Resistant Equipment

A practical glossary guide to equipment designed and tested to control the effects of an internal arcing fault under specified conditions.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

What Arc-Resistant Equipment Means

Arc-resistant equipment is designed and tested to manage certain effects of an internal arcing fault, such as hot gases, pressure, and ejected material, in a defined direction or away from designated areas. The term describes a design approach and tested performance under stated conditions; it does not mean that an arc fault cannot occur, that equipment is immune to damage, or that people are protected in every circumstance. An internal arc can release intense heat and pressure in a short time, so the arrangement of enclosures, covers, doors, barriers, and pressure-relief paths matters. A specific assembly’s performance depends on its construction and on the conditions used for evaluation. Engineers and project teams should therefore treat “arc-resistant” as a qualified description, not a stand-alone safety rating. To interpret it meaningfully, identify the equipment type, applicable standard or test basis, and the limits attached to the tested configuration.

How Design Directs Arc Effects

Design measures may include reinforced compartments, secure closures, internal barriers, and a planned route for pressure and hot gases to discharge. That route must be considered in relation to installation: a design that directs gases upward, for example, needs suitable clearance and an appropriate discharge area. Adjacent walls, ceilings, cable spaces, ducts, and other equipment can affect whether the intended path remains unobstructed. The internal arrangement also matters. Bus placement, compartment boundaries, access points, and the location of potential fault sources all influence how effects may travel through an assembly. These features work together as a system; adding a barrier or changing a layout does not automatically preserve tested performance. During project development, compare the proposed lineup, room conditions, and service access needs with the documented design and test conditions. Qualified professionals should resolve conflicts between installation constraints and the intended direction of discharge before equipment is specified or installed.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Read the Test Conditions Carefully

A test result applies to the configuration and conditions evaluated, not to every assembly that shares a product label or general design family. Relevant parameters can include the equipment’s voltage class, available fault current, duration, grounding arrangement, compartment structure, lineup arrangement, and access conditions during the test. The applicable standard or evaluation method should also be identified, since requirements vary by equipment type and jurisdiction. Ask which configurations were evaluated and whether the proposed arrangement—including end sections, extensions, control compartments, and cable access—matches those limits. Also clarify how the equipment is intended to be installed and what clearances, ventilation, or exhaust paths are required. A stated test current or duration is not a substitute for confirming the project’s actual system conditions. For medium- or high-voltage equipment, identify and verify the standards that apply to that specific equipment. Qualified engineering professionals determine protection, ratings, and code requirements for each installation.

Understand Scope and Operating Limits

Arc-resistant construction does not replace an electrical safety program, protective coordination, or safe work practices. Protection settings and clearing time can affect the energy released during a fault, while maintenance condition, installation quality, and system changes can affect risk. The enclosure’s intended performance may rely on doors being closed and secured, covers being in place, and pressure-relief openings remaining unobstructed. Operating or accessing equipment outside the conditions evaluated may change the protection provided. The designation also does not establish that every potential arc location or operating state is covered. Review operating procedures, access requirements, inspection responsibilities, and the manufacturer’s instructions alongside the equipment specification. An arc-flash risk assessment and other required safety analyses remain separate tasks performed by qualified professionals. Do not interpret arc-resistant equipment as permission to work energized or to reduce required protective measures. Instead, use the design as one part of a broader, project-specific approach to managing electrical hazards.

Information to Provide When Specifying

When requesting a design or evaluating a proposal, provide the one-line diagram, system voltage, available fault-current information, protection and clearing-time assumptions, grounding method, and the intended equipment arrangement. Describe room dimensions, ceiling height, nearby walls, access routes, cable entry, ventilation, and any constraints on pressure or gas discharge. State whether operators may be present at the equipment front, rear, or sides during normal operation, and identify the access conditions that the project expects to maintain. Ask for the applicable test basis, the configuration and conditions covered, installation clearances, and any operating limitations or exclusions. Confirm how project-specific changes would be reviewed before they are incorporated. A manufacturer can use these inputs to assess whether a proposed design aligns with the application and to identify questions that need engineering resolution. For new switchgear, early coordination among the owner, engineer, contractor, and manufacturer helps prevent room-layout or specification decisions from undermining the intended design.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE