MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
A long row of gray Allen-Bradley control cabinets with black switch handles on pallets indoors.
AMERICAN BUILT   /   CALIFORNIA SERVED

University Central Plant Power

Coordinate electrical distribution for shared campus heating and cooling equipment, from major motor loads and control interfaces to maintenance and future capacity.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Map the plant’s electrical loads

A university central plant concentrates electrical demand for equipment serving multiple buildings, so the first design task is to understand how each load operates—not simply total its nameplate ratings. Identify chillers, pumps, cooling towers, boilers, air compressors, heat-recovery equipment and auxiliary systems, then document voltage, phase, full-load current, motor-starting method, operating sequence and expected duty. Include controls, instrumentation and any electric heating or backup equipment that may run during unusual conditions. Seasonal schedules matter: a plant may have high cooling demand in summer, different pumping patterns in shoulder seasons, and overlapping loads during transitions. Distinguish normal, standby and maintenance configurations, and note which loads must remain available when equipment is isolated. These inputs help establish a credible demand profile and inform bus, feeder and protective-device design. Qualified electrical professionals should verify load calculations, applicable codes and ratings against actual equipment data before the distribution design is finalized.

Coordinate switchgear with operating sequences

Central-plant equipment is interconnected operationally as well as electrically. Chiller staging, pump sequencing, tower-fan operation and boiler controls can affect starting demand, minimum flow requirements and which feeders must be energized together. Share the plant’s control narrative and one-line diagram with the electrical design team, including interlocks, permissives, alarms and the intended response to loss of a source or device. Clarify which functions reside in equipment packages and which are expected at the switchgear or elsewhere in the control system. Communication protocols and hardwired interfaces should be defined early, with ownership of signals, wiring boundaries and testing responsibilities made clear. Avoid assuming that a switchgear control feature is interchangeable with a process-control function; each interface needs a defined purpose and responsible party. Reviewing the sequence with campus operators can expose practical concerns, such as how equipment is taken out of service, restarted after an outage or operated during a controls failure.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Plan continuity without overbuilding

Because a central plant serves several campus buildings, its electrical arrangement can affect teaching, research, housing and clinical operations. Determine the consequence of losing each source, bus section, transformer or major feeder, and identify the loads that warrant alternate supply or operational backup. Redundancy may be provided through separate equipment, alternate sources, cross-ties or operating procedures; each approach has different cost, footprint and operating implications. A tie that improves flexibility also introduces questions about normal position, interlocking, fault contribution and the conditions for transfer. Define whether maintenance must be possible without interrupting selected plant functions, and confirm that the physical layout allows safe access to isolate and inspect equipment. Where generators or other emergency sources are involved, document transfer behavior and the loads they are intended to support. Protection, switching practices and emergency operation must be determined by qualified professionals for the project’s system and hazards, rather than inferred from a generic redundancy label.

Coordinate protection, ratings and environment

Protection design must account for the connected utility or generation sources, transformer characteristics, motor starting, available fault current and downstream equipment. Provide current system studies and relevant utility data where available, and identify planned changes that could alter fault levels. Protective-device settings need to balance equipment protection, selective coordination where required, and continuity for the loads that should remain online during a fault. Confirm interrupting and withstand requirements, voltage class, enclosure and environmental conditions for each assembly as design inputs; these are project-specific matters to verify, not assumptions based on the plant’s name. Account for heat, dust, moisture, corrosive exposure, vibration and working clearances in the proposed location. For low-voltage switchboards, UL 891 may be relevant where applicable; medium- or high-voltage equipment requires identification and verification of standards applicable to that specific equipment. Standards compliance alone does not establish a third-party listing. Final selection and code interpretation belong with qualified professionals familiar with the site.

Prepare for installation and future campus needs

A central plant project often combines new equipment with existing distribution, constrained shutdown windows and a long planning horizon. Before requesting a switchgear proposal, provide the one-line diagram, load and motor schedules, control sequence, source information, fault-study assumptions, room drawings, cable-entry preferences and installation constraints. Identify which existing equipment remains, planned tie-in points, access routes and any campus outage periods that shape construction. Discuss spare feeders, future chiller or pump additions, metering needs and space for maintenance; usable expansion capacity depends on the complete design, not merely empty space in an enclosure. For an existing plant, modernization work should be scoped around the customer’s own equipment and the intended interfaces, with condition, compatibility and outage planning reviewed first. Switchgear Builder California builds new equipment in the USA with American components and serves California and nationwide customers. Schedule-sensitive or expedited options may be reviewed against project scope, engineering requirements and manufacturing capacity, but timing must be confirmed for each project.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE