MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear cabinets with red circuit markings and breaker handles arranged on pallets.
AMERICAN BUILT   /   CALIFORNIA SERVED

Oil and Gas Hazardous-Area Interfaces

Define where classified locations begin and end, then coordinate switchgear interfaces with the site’s documented hazards, electrical design, and applicable requirements.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Map classified boundaries before selecting equipment

Oil and gas facilities may include classified locations near process equipment, storage, loading, ventilation openings, or points where flammable gases or vapors could be present. The boundary is a design input, not a visual guess. Use the project’s hazardous-area classification documents, drawings, and process information to identify the specific locations and extent of each classification. Confirm that the documents reflect current equipment arrangements and operating conditions, and resolve discrepancies with the responsible engineering team before equipment interfaces are finalized. Switchgear may be located outside a classified boundary while serving loads or controls within one, but the physical location and connected circuits must be evaluated separately. Clear boundary information helps avoid both unsuitable equipment placement and unnecessary design constraints. Include boundary references in procurement and interface documents so manufacturers, installers, and reviewers are working from the same controlled basis.

Verify suitability for the actual location

A hazardous-location designation is not established by an enclosure description or by the fact that equipment serves an oil and gas facility. Suitability depends on the specific classification system used, the classified area, the substance and conditions identified by the project, and the equipment’s intended installation. Qualified professionals must determine applicable protection methods, ratings, codes, and approvals for each application. Do not assume that a switchgear assembly has hazardous-location certification or that a general-purpose assembly is suitable for installation inside a classified area. If equipment is proposed within a boundary, the design team should identify the governing requirements and verify that the complete equipment and installation approach satisfy them. If it is outside the boundary, verify that the location remains outside under the approved classification documents and that no other environmental or electrical requirement changes the selection.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Coordinate the interface between switchgear and field equipment

Switchgear interfaces can cross a boundary even when the assembly itself does not. Feeder circuits, motor connections, instrument wiring, control power, communications, and grounding paths may extend between ordinary and classified locations. Review each interface for its destination, route, termination, protective device, and any required separation or protective method. Confirm whether field equipment, junction boxes, wiring methods, seals, barriers, or other components are governed by location-specific requirements. These decisions belong to the project’s qualified electrical and hazardous-area professionals; switchgear documentation should not substitute for their classification or installation design. A useful interface schedule identifies the connected load, circuit function, voltage and current requirements, control signals, boundary crossing, and responsible discipline. Early coordination can reveal mismatched assumptions, such as a field device being relocated across a boundary after switchgear procurement information has been issued.

Provide a coordinated technical package

For a useful equipment review, provide the latest one-line diagram, plan drawings with classified-area limits, equipment location, load data, fault-current information, protective-device requirements, and interface schedules. Include the classification basis and relevant area documentation, along with environmental conditions such as temperature, exposure, corrosion concerns, and indoor or outdoor installation. Identify the applicable codes, standards, and project specifications for the particular equipment rather than treating an oil and gas designation as a universal requirement. Requirements differ with equipment type and voltage class; UL 891 applies to applicable low-voltage switchboards, not to all medium- or high-voltage equipment. For medium- or high-voltage equipment, identify and verify the standards applicable to that specific equipment. A complete, consistent package supports a meaningful engineering review and helps clarify what remains for the owner, engineer, manufacturer, and installer to confirm.

Resolve open items before release and installation

Before releasing equipment for manufacture, close questions about boundary limits, equipment placement, ratings, protective coordination, control interfaces, and responsibility for field-installed components. Document approved deviations and drawing revisions, and confirm that procurement documents match the current engineering basis. If classification drawings or process conditions change, assess whether the equipment location, connected circuits, or installation requirements are affected; do not assume an earlier review remains valid. During installation, qualified personnel should verify the location and configuration against approved drawings and applicable requirements, with any discrepancies escalated through the project’s formal review process. Switchgear Builder California builds new switchgear in the USA using American components and supplies equipment to customers. Project requirements should be reviewed before configuration is established; schedule-sensitive options, if appropriate, depend on project review and cannot be assumed. This disciplined handoff helps keep hazardous-area assumptions visible from design through commissioning.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE