MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear beneath overhead conduits in an industrial room, with gallery arrows overlaid on the image.
AMERICAN BUILT   /   CALIFORNIA SERVED

Automatic Transfer Switches for Hospitals

A hospital transfer scheme must do more than change sources: it must support the facility’s essential electrical sequence, safe maintenance and coordinated recovery.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Map Essential Loads to the Transfer Scheme

Begin with the hospital’s electrical distribution documents and identify which loads depend on each normal and standby source. Clinical services, life-safety functions, critical equipment, building systems and support areas may have different continuity needs, and their arrangements should be determined by the facility’s qualified electrical and healthcare design professionals. An automatic transfer switch (ATS) is one part of that system; its source connections, downstream distribution and relationship to other transfer devices all affect the result. Document the intended load groups, source assignments, operating priorities and any loads that are intentionally excluded from automatic transfer. This helps prevent a common planning error: treating all hospital loads as one undifferentiated block. Clear load mapping gives the project team a basis for evaluating transfer behavior, defining equipment interfaces and reviewing whether the proposed sequence supports clinical operations during an outage and restoration.

Define the Normal-to-Standby Operating Sequence

A transfer sequence should describe what the system senses, what conditions initiate action, and how it responds when the normal source becomes unacceptable. The design team should establish applicable voltage and frequency limits, time delays, source availability criteria and the permitted sequence for transferring each load group. These are project-specific design inputs, not assumptions to leave to field interpretation. Consider how the ATS behaves if the standby source is not ready, fails during transfer, or becomes unstable after carrying load. Also define whether loads transfer in stages, whether any functions require a delayed or controlled return, and what indications operators need to understand current source status. The sequence must account for connected equipment and upstream protection, not merely the switch’s nominal function. Review the intended behavior with the electrical engineer, generator and control-system teams, facility operators and other affected disciplines before equipment details are finalized.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Coordinate Standby Source and Recovery

Standby power performance depends on the complete source path. Confirm the generator or other standby source arrangement, available capacity, grounding and bonding approach, protective devices, control interfaces and expected response under the hospital’s defined load profile. A source that is electrically available may not yet be suitable for transfer; the control philosophy should state how readiness is established and what happens when limits are not met. Recovery deserves equal attention. Establish how and when loads return to the normal source, whether retransfer is automatic or operator-directed, and how the facility will manage a second disturbance during restoration. Where multiple ATS units or distribution sections are involved, coordinate their sensing and timing so that independent devices do not create an unintended sequence or overload the standby source. Qualified professionals should verify the applicable ratings, fault-current conditions, protection coordination and code requirements for the actual installation.

Plan Maintenance Isolation Without Losing Visibility

Hospital equipment must be maintainable, but isolation arrangements should be evaluated against the continuity needs of the loads served. Identify how each ATS can be inspected, tested and serviced, what electrical sources must be isolated, and whether the planned arrangement allows a safe work condition without unexpectedly interrupting essential functions. Maintenance bypass or isolation provisions, where considered, require careful review of the switching path, interlocking, operating procedures and personnel access. Their suitability depends on the system design and applicable requirements; they should not be treated as a universal feature. Include provisions for clear source and position indication, safe access, lockout procedures and documented restoration steps. Coordinate routine testing with facilities staff and clinical operations so that test conditions, notifications, load impacts and return-to-normal actions are understood in advance. The project team should review maintainability early, while the one-line diagram, equipment arrangement and operating sequence can still be coordinated.

Confirm Healthcare Requirements and Project Inputs

Healthcare electrical requirements depend on facility type, spaces served, adopted codes and standards, authority interpretations and the project’s design criteria. The owner’s electrical engineer and other qualified professionals should determine which requirements apply, including rules for essential electrical systems, source separation, branch functions, testing and documentation. Provide the equipment builder with the current one-line diagram, load and source data, control narratives, available fault-current information, enclosure and environmental conditions, connection details, interface requirements and any specified standards. Identify whether the work is new construction or a change to an existing distribution system, and explain constraints that affect access or outage planning. Review submittals for sequence, ratings, dimensions, terminal locations, controls and maintenance clearances before release. A focused design review can expose gaps between drawings and operating expectations early. For schedule-sensitive projects, discuss feasibility and constraints during project review; timing and equipment details depend on the confirmed scope.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE