MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Three gray switchgear cabinets with open doors and breaker panels on wooden pallets indoors.
AMERICAN BUILT   /   CALIFORNIA SERVED

Surge Protective Device Selection

A practical framework for aligning surge protection devices with the electrical system, equipment layout, and project documents.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Start with the Electrical System

Select a surge protective device (SPD) only after establishing the electrical system it must protect. Confirm nominal voltage, frequency, phase, grounding method, and whether the service is grounded, impedance-grounded, or ungrounded. Determine the maximum continuous operating voltage required for each intended connection; an SPD’s voltage selection must suit normal system conditions, not merely the nominal voltage shown on a one-line diagram. Review available fault current and the overcurrent protective device requirements, since the SPD and its connections must be applied within the limits of the specific equipment and installation. Identify whether the device is intended for service equipment, a distribution section, or a downstream panel, and whether the goal is to protect equipment at one point or coordinate protection across the facility. These are design inputs, not interchangeable catalog choices. The engineer of record and qualified electrical professionals should confirm applicable codes, protection needs, and ratings for the project.

Choose a Location That Supports Protection

Location affects both what the SPD protects and how effectively it can limit transient voltage at the equipment. A device installed near the service entrance can address surges entering from the supply, while devices nearer sensitive loads can help manage residual surges and events generated within the facility. Long conductors between an SPD and the protected bus add inductive voltage during a surge, so placement, conductor routing, and connection length deserve attention in the physical layout. Coordinate the proposed mounting position with bus arrangement, cable space, access for inspection, and the manufacturer's installation instructions. For switchgear with multiple sections, verify which bus or section the device will connect to and whether the intended protection reaches the loads that matter. Do not assume that a device in one section protects every downstream circuit equally. Review the one-line, elevations, and wiring requirements together before finalizing the location.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Match Protection Modes to the System

SPDs can be configured to protect between line and neutral, line and ground, neutral and ground, or line conductors, depending on the device and the system grounding arrangement. These modes are not a universal checklist: the appropriate combination depends on the supply configuration, SPD design, and the voltage stresses the protected equipment may experience. For example, line-to-neutral protection may be relevant on a grounded wye system, while a delta or ungrounded system calls for a different review of available modes and voltage relationships. Confirm the device’s connection diagram and permitted system types rather than inferring compatibility from a voltage rating alone. Consider the equipment’s insulation and the loads served, including controls, electronic drives, and communications interfaces where applicable. The design team should also clarify whether protection is required at the service, distribution, or load level. Qualified professionals must evaluate grounding and bonding so surge current paths do not undermine personnel safety or system performance.

Coordinate Ratings and Protective Devices

Compare the SPD’s documented characteristics with the system and the project’s performance objectives. Relevant information may include voltage protection ratings, nominal discharge current, short-circuit current rating, maximum continuous operating voltage, and the required overcurrent protective device. The significance and test basis of each value depend on the applicable product requirements and installation context; a higher number in isolation does not establish better protection. Check whether the specified SPD is integral to the switchgear or supplied as a separate component, and define the connection method, disconnecting means, status indication, and any required alarm contacts. Confirm that the specified arrangement can be accommodated without conflicting with clearances, access, or other equipment. Coordinate with upstream and downstream protective devices and with the equipment manufacturer’s instructions. Ask the design team to resolve any discrepancy between device data, drawings, and the project specification before release, rather than leaving selection to an assumption during assembly.

Make the Specification and Submittal Actionable

A useful SPD specification identifies the system voltage and grounding configuration, intended installation point, required protection modes, and the performance and connection requirements that apply. State whether the device is wanted at service equipment, a distribution board, or another defined location; name the equipment section or bus where practical. Include applicable standards for the specific SPD and switchgear, along with project-specific fault-current, overcurrent protection, indication, and monitoring requirements. Do not use a standard reference as evidence of a third-party listing or approval; identify and verify the requirements applicable to each assembly and component. Provide the one-line diagram, equipment schedule, site conditions, load priorities, and any owner or engineer criteria to support review. On submittals, compare the offered configuration with those documents and resolve exceptions explicitly. For a new switchgear build, early coordination helps establish space, connections, and responsibilities before drawings are finalized. Schedule-sensitive options, if needed, require project review and should not be assumed.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE