MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Three gray switchgear cabinets with open doors and breaker panels on wooden pallets indoors.
AMERICAN BUILT   /   CALIFORNIA SERVED

Short-Circuit Current Ratings

A sound SCCR decision starts with the fault current available at the installation point and a review of the complete electrical system.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Start with available fault current at the equipment

The short-circuit current rating (SCCR) is a key input when selecting an assembly for a particular electrical system. Begin by establishing the maximum prospective fault current available at the point where the equipment will be installed. That value depends on the source, transformer characteristics and impedance, conductor length and size, and other system components. It may differ from the fault current at the service entrance or another point in the facility, so use a calculation for the actual connection location rather than an assumed site-wide figure. Obtain the latest one-line diagram, utility or source data, transformer information, and feeder details; identify any planned changes that could raise available current. A qualified electrical professional should determine the study method, assumptions, and applicable code requirements. The resulting value is a design input for specifying the assembly, not a substitute for checking its ratings and coordination within the entire installation.

Distinguish SCCR from interrupting and withstand ratings

Several ratings appear in short-circuit studies, and they describe different performance limits. An overcurrent protective device’s interrupting rating concerns its ability to interrupt a specified fault current under defined conditions. An assembly SCCR addresses the short-circuit current the equipment can withstand or safely manage when applied as specified. A switchgear lineup may also have a short-time withstand rating used for a defined duration, which matters when protection is intentionally delayed for coordination. These values are related, but they are not interchangeable: a breaker with an adequate interrupting rating does not, by itself, establish an adequate rating for the complete assembly. Likewise, a bus withstand value does not confirm that every connected component is suitable. Review the equipment documentation and project requirements together, including any stated conditions, duration, and protective-device arrangement. Have qualified professionals verify that each relevant rating covers the available fault current and intended operating scheme.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Review protective devices and any conditional rating basis

Protective-device selection and settings affect how fault energy is limited and how equipment is exposed during a fault. If a proposed assembly rating depends on a specific upstream protective device, fuse, or tested combination, that condition must be clear in the design and maintained in the installation. Confirm the device type, manufacturer and model where required, current rating, settings, and location relative to the assembly. Do not assume that a higher-rated upstream breaker automatically increases the assembly SCCR, or that a current-limiting device can be substituted without checking the applicable conditions. Coordination goals can also introduce tradeoffs: delayed tripping may support selective coordination but can affect the duration for which equipment must withstand current. The engineer responsible for protection should assess the system study, device characteristics, and applicable requirements. Provide the intended protection scheme when requesting a design review so the rating basis can be examined rather than inferred.

Account for installation and system changes

The required SCCR is tied to the conditions at the installation point, not merely to a nominal voltage or equipment nameplate. Confirm system voltage, grounding arrangement, source configuration, transformer size and impedance, conductor routing, and the presence of generators, motors, or parallel sources that could contribute current. Consider operating configurations such as tie breakers, alternate feeds, and normally open points; a lineup may see different fault levels in different states. The highest credible available fault current for the applicable configuration generally deserves attention, while assumptions should be documented for review. Future utility upgrades, transformer replacement, generator additions, or feeder changes can alter the study result, so project teams should identify known planned work. Environmental and physical installation details may also affect equipment selection and construction, although they do not replace the fault-current calculation. Qualified professionals should verify the final system conditions and applicable codes before procurement and again when material design changes occur.

Provide a complete basis for equipment selection

For a useful specification review, provide the one-line diagram, the calculated available fault current at the equipment terminals, system voltage and frequency, source and transformer data, feeder information, protective-device schedule and settings, and any required short-time withstand duration. Include the study date, assumptions, operating configurations, and applicable project or code requirements. State whether the value is preliminary or final, and identify open decisions such as a pending transformer selection. The equipment manufacturer can then review the requested rating and any associated conditions against the proposed design scope. Requirements should be confirmed for the specific assembly; do not treat one project’s rating or construction as evidence for another. If study results are incomplete, resolve the uncertainty with the engineer of record before finalizing the specification. This disciplined exchange helps avoid selecting equipment against an outdated fault-current value and supports a coordinated, reviewable design from procurement through installation.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE