MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
A row of gray electrical cabinets beneath overhead cables along an industrial corridor.
AMERICAN BUILT   /   CALIFORNIA SERVED

800 Amp Busway

Plan an 800 A busway configuration around continuous current, installation conditions, tap-off connections and coordinated protection.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Define the 800 A Continuous Rating

An 800 A busway specification begins with the continuous current the system must carry, not simply the sum of equipment nameplate values. Establish the expected demand, operating pattern and anticipated peak conditions for the served distribution. Then confirm that the selected busway rating is appropriate for the actual installation and the project’s applicable requirements. Ambient temperature, enclosure conditions, installation orientation and other manufacturer-defined factors can affect the allowable rating; have qualified electrical professionals evaluate those conditions rather than treating 800 A as a universal field capacity. Also distinguish the continuous rating of the busway from the ratings of connected components. A plug-in unit, tap-off device, protective device or feeder may have a lower rating and become the limiting element. The design should state what the 800 A figure applies to, where the rating is measured, and which environmental and operating assumptions need confirmation before final selection.

Map the Route Before Selecting Sections

A busway route is both an electrical path and a physical installation plan. Document the start and end points, elevation changes, horizontal runs, direction changes, obstructions, access clearances and the locations where the route passes through building elements. Identify whether the run is intended for indoor or outdoor conditions and describe exposure to moisture, dust, heat or other environmental concerns. These details help determine the required straight lengths, fittings, supports and connection points, subject to review against the selected manufacturer’s system. Coordination with structural, architectural, mechanical and fire-protection plans is important: a route that fits electrically may still conflict with ductwork, access requirements or building movement provisions. Include installation tolerances and practical access for assembly, inspection and future maintenance. Early route review reduces field modifications and helps the project team identify where dimensions, supports and interfaces must be verified before procurement and installation.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Coordinate Tap-Off Locations and Loads

Tap-off connections should correspond to the distribution plan, equipment locations and anticipated load profile. For each connection, identify the served equipment, expected demand, required protective device characteristics and connection orientation or access needs. Confirm that the proposed tap-off arrangement is compatible with the specified busway system and intended operating conditions. Do not assume every tap-off can carry the full 800 A busway rating; the tap-off, its protective device, downstream conductors and connected equipment each have distinct ratings that must be checked. Consider whether loads are continuous, intermittent, nonlinear or likely to operate simultaneously, since these factors influence demand and protection decisions. For commercial distribution, coordinate branch locations with tenant spaces, panels, equipment rooms and maintenance access. A clear schedule of tap-off points, loads and required devices gives the designer and builder a useful basis for review while leaving final selection and protection decisions to qualified professionals.

Verify Bus and Protection Ratings Separately

A complete specification distinguishes the busway’s continuous current rating from its short-circuit withstand capability, the interrupting rating of protective devices and the ratings of all connected equipment. These values address different conditions and cannot be substituted for one another. Provide available fault-current information, source characteristics and the intended protective-device arrangement so the project team can evaluate coordination and equipment suitability. Confirm the main protection location and function, whether it is integral to an assembly or provided upstream, and how it relates to downstream tap-off protection. The protection scheme should be evaluated for the actual installation, including conductor and equipment limits and applicable codes. Qualified professionals must determine protection, ratings and code requirements for each project. Identify standards that apply to the specific equipment under consideration and verify them with the responsible design and procurement teams; a stated design requirement should not be confused with evidence of a third-party listing or approval.

Plan for Growth and Submit Design Inputs

Future-load allowance is most useful when it is based on a documented expansion plan rather than an arbitrary spare-capacity percentage. Identify likely additions, their anticipated demand and when they may be connected. Then assess whether the busway rating, source capacity, upstream protection, tap-off positions and downstream distribution can accommodate that growth. Spare physical connection points do not by themselves establish spare electrical capacity, and unused rating should not be treated as available without a coordinated load and protection review. To develop an 800 A configuration, provide one-line diagrams, load schedules, source and fault-current data, route drawings, environmental conditions, tap-off requirements, installation constraints and applicable project standards. Note unresolved assumptions and requested submittal details. A manufacturer can use this information to review the proposed scope and identify questions or configuration considerations. Final ratings, protection settings and installation decisions remain subject to project-specific engineering review and confirmation.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE