MANUFACTURED IN THE USA   /   SHIPPING NATIONWIDESALES & PROJECT SUPPORT   (951) 403-5738
Gray electrical switchgear with breakers in an industrial room, with loose conduit and fittings in the foreground.
AMERICAN BUILT   /   CALIFORNIA SERVED

2000 Amp Switchgear and Distribution Equipment

A 2000 A designation is only a starting point. Define how the equipment will operate, what the installation requires and which configurations can be confirmed for your project.

NEW SWITCHGEAR / AMERICAN COMPONENTS / BUILT TO SPEC01 — CALIFORNIA + NATIONWIDE
01
Made in the USAAmerican manufacturing
02
UL 891 switchboardsLow-voltage assemblies, as applicable
03
Short lead timesSchedule confirmed with quote
04
Nationwide shippingServing California & beyond
BUILT AROUND YOUR PROJECT / 01

Define what 2000 A means for the installation

A 2000 A rating identifies a current level, but it does not by itself establish that an assembly suits a particular service. Start by documenting the system voltage, phase, frequency, grounding arrangement, available fault current and the equipment’s role in the distribution system. Clarify whether 2000 A is the required continuous-current rating of the complete assembly, a bus rating, or the rating associated with a particular main or feeder device. These distinctions affect equipment selection and coordination. Also identify load characteristics, including expected demand, motor starting, nonlinear loads and any planned expansion. Qualified electrical professionals must determine applicable ratings, protection and code requirements for the project. Provide one-line diagrams and preliminary load information early, then resolve open design items before drawings are finalized. A clear basis of design helps the manufacturer assess the requested configuration and identify which details need confirmation.

Evaluate continuous-current conditions

Continuous-current requirements should reflect how the equipment will actually be loaded, not only the nominal service size. Identify expected operating current, loading patterns, ambient conditions, enclosure and installation environment, and whether equipment will sit indoors or outdoors. Temperature, ventilation, conductor arrangement and nearby heat sources can affect design decisions and require review against applicable equipment requirements. Explain whether the service is expected to operate near its rating for long periods, and note unusual duty cycles or future load additions. Do not assume that a 2000 A label means every component, termination or connected conductor has the same rating; the complete distribution path must be evaluated. The engineer of record and other qualified professionals should establish the governing design criteria, including protection and any required derating. With those criteria documented, the builder can review the requested assembly and clarify the ratings and configuration that can be offered for the application.

THE DETAILS THAT DRIVE THE BUILD
Project specifications to define with your quote
SystemVoltage, phase, current and available fault current
ConfigurationLineup, protection, controls and enclosure as specified
ComplianceApplicable standards and listing confirmed for the assembly
DeliveryCalifornia and nationwide; schedule confirmed by quote

Coordinate fault current and bus bracing

Bus bracing must be considered in relation to the available fault current and the protective devices expected to clear a fault. Share the utility or upstream source information, transformer data, conductor lengths and sizes, and protective-device details when available. These inputs help qualified professionals determine the prospective fault duty at the equipment and coordinate interrupting ratings, withstand requirements and protection settings. A 2000 A continuous-current rating does not establish short-circuit capability; the two address different conditions. Changes to the source, transformer, feeder arrangement or upstream protection can change fault-current calculations, so assumptions should be recorded and revisited when the design changes. Identify the applicable standards and project specifications for the particular equipment, then confirm which ratings and documentation are required. Do not treat a requested bracing value as confirmed until the design has been reviewed for the specific assembly and system conditions. Clear coordination reduces late revisions and supports a safer, more complete submittal.

Plan physical layout and delivery splits

A 2000 A assembly may require careful attention to dimensions, access and how sections will be handled at the site. Provide room dimensions, door and corridor clearances, floor and anchorage constraints, cable entry direction, overhead restrictions, and the location of adjacent equipment. Note lifting limitations and the intended route from receiving point to the final installation position. If shipment or site access requires the assembly to be divided into sections, discuss that need during design rather than after fabrication planning. Delivery splits can affect bus connections, field assembly, handling, shipping dimensions and the work required to restore the intended assembly at the site. Confirm who will perform installation and interconnection, what drawings and instructions they need, and how site sequencing affects the proposed arrangement. The final split and shipping plan depend on the approved design and project review. Early coordination gives the team time to compare a compact layout with practical handling and installation requirements.

Confirm configuration and availability early

Equipment availability depends on the requested electrical design, component selection, enclosure, documentation and project schedule. A 2000 A description alone is not enough to confirm that a particular configuration is available. Submit the specification, one-line diagram, load and fault-current data, preferred arrangement, site constraints, required options and target schedule for review. Identify which items are mandatory and which could be considered alternatives, so the team can evaluate tradeoffs without compromising project requirements. Ask for confirmation of the proposed equipment scope, ratings, interfaces, drawings, delivery splits and any schedule-sensitive options; expedited possibilities require project review and are not guaranteed. California customers and projects elsewhere in the United States can discuss equipment supply and shipping needs, subject to project-specific review. Before purchase, reconcile the proposal with the engineer’s design, procurement documents and installation plan. This practical check helps prevent assumptions about availability or timing from becoming costly changes later.

READY WHEN THE PROJECT IS

Let's get power moving.

From the first specification to the final shipment, start with a conversation about your project.

REQUEST A QUOTE